Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.

This item may need to be sourced from germ...(choose a part on the right to read more)

General Fitment

Don't install those shiny new floorboards using your old beat up rusty hardware. Rennline now offer's stainless steel floor board mounting kits. Each kit comes with a specially embossed stainless steel spacer, washer and nut.

*rennline's driver side 911(1965-89) floorboards do not require a hardware kit.

General Fitment

Kit includes

-new compressor with clutch, compatible with r134a and r12
-ester refrigerant oil, compatible with r134a or r12
-r134a charge port adapters.
-kuehl kwick mounting bracket & hardware
-new compressor to rear deck lid condenser barrier hose line assembly with sae approved crimped fittings and our high-low pressure switch feature. The condenser side fitting of the hose assembly will be flare.
-new compressor to evaporator barrier short hose; with sae crimped fitting on the compressor side. This allows you to cut & splice to old suction line in the engine compartment using a barb fitting with clamps supplied in the kit.
-new receiver drier, Porsche configuration.
-detailed installation instruc...(choose a part on the right to read more)

General Fitment

Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)

This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)

This muffler is manufactured in europe by dansk. They offer a complete line of OEM replacement mufflers and tuning mufflers to complement the entire Porsche model range. We categorize the sound levels from mild street mufflers (TUV approved), exotic sounding sport mufflers and wide open, pulse pounding, race mufflers. Mufflers are manufactured to the highest of European standards from stainless steel or painted galvanized steel. They are available with differing inlet / outlet configurations and varying diameter tips. Each dansk quality muffler offers the reliability and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany and ...(choose a part on the right to read more)

General Fitment

This muffler is manufactured in europe by dansk. They offer a complete line of OEM replacement mufflers and tuning mufflers to complement the entire Porsche model range. We categorize the sound levels from mild street mufflers (TUV approved), exotic sounding sport mufflers and wide open, pulse pounding, race mufflers. Mufflers are manufactured to the highest of European standards from stainless steel or painted galvanized steel. They are available with differing inlet / outlet configurations and varying diameter tips. Each dansk quality muffler offers the reliability and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany and ...(choose a part on the right to read more)

General Fitment

FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)

Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.8-inch (71 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is remanuf...(choose a part on the right to read more)

Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increase safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. FVD BrombacherGermany conveniently combines Porsche specific h&r spacers, the correct Porsche bolt shoulders and the correct length h&r bolts to take the guess work out of adding spacers to your car. Our spacers are cost competitive and have been developed to work together without compromise. Don't be fooled by the competition whose costs quickly add up by requiring you to order the spacers...(choose a part on the right to read more)

Ok, we know you are a driving enthusiast if you are shopping for a short shifter for your manual transmission. Driving enthusiasts appreciate a more direct connection to the car, transmission and road surface. If you are trying to clean up those long shifts and side to side play on the factory shifter you are certainly on the right track with this upgrade. This numeric racing short shift kit uses precision ball bearings on all axis' which produce 35% shorter throws with an almost gated like action. Short gated like throws increase your driving experience by enhancing a more direct, mechanical connection to your car. Once installed you will find joy with every shift and this will easily become one of your favor...(choose a part on the right to read more)

K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)

This muffler is manufactured in europe by dansk. They offer a complete line of OEM replacement mufflers and tuning mufflers to complement the entire Porsche model range. We categorize the sound levels from mild street mufflers (TUV approved), exotic sounding sport mufflers and wide open, pulse pounding, race mufflers. Mufflers are manufactured to the highest of European standards from stainless steel or painted galvanized steel. They are available with differing inlet / outlet configurations and varying diameter tips. Each dansk quality muffler offers the reliability and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany and ...(choose a part on the right to read more)

General Fitment

Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original 2.4-inch (63 mm) to a 2.6-inch (66.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. FVD thrott...(choose a part on the right to read more)

FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)

Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.

Fits these applications

lh drive models
Porsche 911 non-turbo, 1984-1989 (pre 964 model)
coupe, cabriolets, and turbo look bodies.
with factory installed ac

Includes

new...(choose a part on the right to read more)

Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more)

General Fitment

Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more)

General Fitment

Is your clutch disc difficult to engage and release? Those are signs that your release bearing is bad. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a kit. 1 necessary per car. Not sure which clutch parts are right for your car? We have pre-packaged kits that include everything that you need for installation. Check them out under the clutch kits category.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Transmission	911 1974-77 - Transmission
911 1978-83 - Transmission	911 1984-86 - Transmission

Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more)

General Fitment

Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more)

General Fitment

The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.

Unlike other kits, the bbi autosport kit is designed be used with OEM clutch master cylinder, hose, and spring pack. This eliminates the need for additional parts, making our kit a complete plug an...(choose a part on the right to read more)

Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more)

General Fitment